China 12V 20rpm DC Gear Motor Planetary 36mm Gearbox planetary gearbox electric motor

Item Description

A. Specification of 12V 20RPM DC Gear Motor Planetary 36MM Gearbox:

one. Voltage: 12/24V
two. Speed: 1.2-2000RPM
three. Torque: .2-50Kgf.cm
four. Output Energy: 1-5W
5. Gearbox Ratio:  one:3.7 to 1: 3736
six. Gearbox Diameter: 36mm
7. Gearbox Length: 25.1-fifty.9mm
eight. Motor Length: 29.1mm
9. Shaft Diameter: 8mm
10. Shaft Length: Customized

Note: The info sheet is only for reference, We can make the motor according to your need right after Evaluation

How to calculate the motor with gearbox output specs?
1. Output Speed(No-load)=Motor Speed(No-load)/Reduction Ratio
2. Output Torque=Motor Torque*Reduction Ratio*Gearbox Efficiency
 
e.g.: 
PG36GR124500-19.2K
1. Output Speed(No-load)=4500/19.2=234RPM
two. Output Torque=sixty seven.6*19.2*81%=1051.3g.cm≈1kg.cm=.1Nm (Should not be higher than Max. Gear Running Torque)

B. Organization Capability

HangZhou CZPT Co. Ltd is a manufacturer and exporter of various of motors with in excess of 10 years knowledge.
Our solution ranges consist of:
1) DC Brush motor: 6-130mm diameter, .01-1000W output energy
two) DC Spur Gear Motor: 12-110mm diameter, .1-300W output energy
three) DC Planeary Equipment Motor: ten-82mm diameter, .1-100W output power 
4) Brushless DC Motor: 28-110mm, 5-1500W output power 
5) Stepper Motor: NEMA 08 to NEMA 43, Can with gearbox and guide screw
six) Servo Motor: 42mm to 130mm diameter, fifty-4000w 
seven) AC Gear Motor: 49 to 100mm diameter, 6-one hundred forty output power 

1. Generation Line:

2. Tests Equipment:

3. Certificates:

four. Customer Visits:

six. FAQ:

Q: What is actually your principal products?
A:We at the moment create Brushed Dc Motors, Brushed Dc equipment Motors, Planetary Dc Gear Motors, Brushless Dc Motors, Stepper motors and Ac Motors and many others. You can check out the technical specs for over motors on our site and you can electronic mail us to advocate necessary motors for each your specification way too.

Q:How to pick a suitable motor?
A:If you have motor photographs or drawings to demonstrate us, or you have in depth specs like voltage, speed, torque, motor measurement, doing work mode of the motor, required daily life time and noise degree and so forth, remember to do not be reluctant to allow us know, then we can recommend suitable motor for each your request appropriately.

Q: Do you have custom-made support for your standard motors?
A:Sure, we can customize for every your ask for for the voltage, speed, torque and shaft measurement/condition. If you need extra wires/cables soldered on the terminal or want to insert connectors, or capacitors or EMC we can make it as well.

Q:Do you have specific style support for motors?
A:Indeed, we would like to layout motors individually for our customers, but it may possibly want some CZPT cost and style demand. 

Q:Can I have samples for tests initial?
A:Of course, definitely you can. Soon after verified the needed motor specs, we will quote and offer a proforma bill for samples, as soon as we get the payment, we will get a PASS from our account office to move forward samples appropriately.

Q:How do you make confident motor high quality?
A:We have our very own inspection processes: for incoming materials, we have signed sample and drawing to make confident certified incoming supplies for creation process, we have tour inspection in the method and last inspection to make positive certified products ahead of transport.

Q:What is actually your lead time?
A:Usually talking, our normal regular item will need twenty five-30days, a bit lengthier for customized merchandise. But we are extremely adaptable on the lead time, it will is dependent on the certain orders

Q:What is actually your payment phrase?
A:For all our new buyers, we will need to have 40% deposite, sixty% paid prior to cargo.

Q:When will you reply soon after acquired my inquiries?
A:We will response inside 24 several hours once get your inquires.

Q:How can I trust you to make positive my cash is secure?
A:We are certified by the 3rd celebration SGS and we have exported to over eighty five nations up to June.2017. You can check our reputation with our recent clients in your place (if our buyers do not head), or you can order by means of alibaba to get trade assurance from alibaba to make positive your money is secure.

Q:What’s the minimum purchase amount?
A:Our least buy amount depends on different motor versions, you should e mail us to check. Also, we usually do not settle for personalized use motor orders. 

Q:What’s your delivery method for motors?
A:For samples and offers significantly less than 100kg, we normally recommend categorical delivery For hefty deals, we typically recommend air shipping and delivery or sea shipping and delivery. But it all depends on our customers’ demands.

Q:What certifications do you have?
A:We currently have CE and ROSH certifications.

Q:Can you deliver me your price list?
A:Given that we have hundreds of distinct merchandise, and cost may differ for every different specifications, we are not CZPT to supply a price listing. But we can quote inside of 24 several hours once obtained your inquirues to make positive you can get the price in time.

Q:Can I visit your company?
A:Yes, welcome to pay a visit to our business, but you should permit us know at the very least 2 months in advance to help us make certain no other meetings throughout the working day you visit us. Many thanks!

Weclome make contact with with us if have any inquiries about this motor or other goods!

Application: Universal, Household Appliances, Power Tools, Curtain and Others
Operating Speed: Low Speed
Function: Driving
Casing Protection: Open Type
Structure and Working Principle: Brush
Type: DC Gear Motor

###

Samples:
US$ 15/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:
Application: Universal, Household Appliances, Power Tools, Curtain and Others
Operating Speed: Low Speed
Function: Driving
Casing Protection: Open Type
Structure and Working Principle: Brush
Type: DC Gear Motor

###

Samples:
US$ 15/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

Planetary Gearbox

This article will explore the design and applications of a planetary gearbox. The reduction ratio of a planetary gearbox is dependent on the number of teeth in the gears. The ratios of planetary gearboxes are usually lower than those of conventional mechanical transmissions, which are mainly used to drive engines and generators. They are often the best choice for heavy-duty applications. The following are some of the advantages of planetary gearboxes.
planetarygearbox

planetary gearboxes

Planetary gearboxes work on a similar principle to solar systems. They rotate around a center gear called the sun gear, and two or more outer gears, called planet gears, are connected by a carrier. These gears then drive an output shaft. The arrangement of planet gears is similar to that of the Milky Way’s ring of planets. This arrangement produces the best torque density and stiffness for a gearbox.
As a compact alternative to normal pinion-and-gear reducers, planetary gearing offers many advantages. These characteristics make planetary gearing ideal for a variety of applications, including compactness and low weight. The efficiency of planetary gearing is enhanced by the fact that ninety percent of the input energy is transferred to the output. The gearboxes also have low noise and high torque density. Additionally, their design offers better load distribution, which contributes to a longer service life.
Planetary gears require lubrication. Because they have a smaller footprint than conventional gears, they dissipate heat well. In fact, lubrication can even lower vibration and noise. It’s also important to keep the gears properly lubricated to prevent the wear and tear that comes with use. The lubrication in planetary gears also helps keep them operating properly and reduces wear and tear on the gears.
A planetary gearbox uses multiple planetary parts to achieve the reduction goal. Each gear has an output shaft and a sun gear located in the center. The ring gear is fixed to the machine, while the sun gear is attached to a clamping system. The outer gears are connected to the carrier, and each planetary gear is held together by rings. This arrangement allows the planetary gear to be symmetrical with respect to the input shaft.
The gear ratio of a planetary gearbox is defined by the sun gear’s number of teeth. As the sun gear gets smaller, the ratio of the gear will increase. The ratio range of planetary gears ranges from 3:1 to ten to one. Eventually, however, the sun gear becomes too small, and the torque will fall significantly. The higher the ratio, the less torque the gears can transmit. So, planetary gears are often referred to as “planetary” gears.
planetarygearbox

Their design

The basic design of a Planetary Gearbox is quite simple. It consists of three interconnecting links, each of which has its own torque. The ring gear is fixed to the frame 0 at O, and the other two are fixed to each other at A and B. The ring gear, meanwhile, is attached to the planet arm 3 at O. All three parts are connected by joints. A free-body diagram is shown in Figure 9.
During the development process, the design team will divide the power to each individual planet into its respective power paths. This distribution will be based on the meshing condition of all gears in the system. Then, the design team will proceed to determine the loads on individual gear meshes. Using this method, it is possible to determine the loads on individual gear meshes and the shape of ring gear housing.
Planetary Gearboxes are made of three gear types. The sun gear is the center, which is connected to the other two gears by an internal tooth ring gear. The planet pinions are arranged in a carrier assembly that sets their spacing. The carrier also incorporates an output shaft. The three components in a Planetary Gearbox mesh with each other, and they rotate together as one. Depending on the application, they may rotate at different speeds or at different times.
The planetary gearbox’s design is unique. In a planetary gearbox, the input gear rotates around the central gear, while the outer gears are arranged around the sun gear. In addition, the ring gear holds the structure together. A carrier connects the outer gears to the output shaft. Ultimately, this gear system transmits high torque. This type of gearbox is ideal for high-speed operations.
The basic design of a Planetary Gearbox consists of multiple contacts that must mesh with each other. A single planet has an integer number of teeth, while the ring has a non-integer number. The teeth of the planets must mesh with each other, as well as the sun. The tooth counts, as well as the planet spacing, play a role in the design. A planetary gearbox must have an integer number of teeth to function properly.

Applications

In addition to the above-mentioned applications, planetary gearing is also used in machine tools, plastic machinery, derrick and dock cranes, and material handling equipments. Further, its application is found in dredging equipment, road-making machinery, sugar crystallizers, and mill drives. While its versatility and efficiency makes it a desirable choice for many industries, its complicated structure and construction make it a complex component.
Among the many benefits of using a planetary gearbox, the ability to transmit greater torque into a controlled space makes it a popular choice for many industries. Moreover, adding additional planet gears increases the torque density. This makes planetary gears suitable for applications requiring high torque. They are also used in electric screwdrivers and turbine engines. However, they are not used in everything. Some of the more common applications are discussed below:
One of the most important features of planetary gearboxes is their compact footprint. They are able to transmit torque while at the same time reducing noise and vibration. In addition to this, they are able to achieve a high speed without sacrificing high-quality performance. The compact footprint of these gears also allows them to be used in high-speed applications. In some cases, a planetary gearbox has sliding sections. Some of these sections are lubricated with oil, while others may require a synthetic gel. Despite these unique features, planetary gears have become common in many industries.
Planetary gears are composed of three components. The sun gear is the input gear, whereas the planet gears are the output gears. They are connected by a carrier. The carrier connects the input shaft with the output shaft. A planetary gearbox can be designed for various requirements, and the type you use will depend on the needs of your application. Its design and performance must meet your application’s needs.
The ratios of planetary gears vary depending on the number of planets. The smaller the sun gear, the greater the ratio. When planetary stages are used alone, the ratio range is 3:1 to 10:1. Higher ratios can be obtained by connecting several planetary stages together in the same ring gear. This method is known as a multi-stage gearbox. However, it can only be used in large gearboxes.
planetarygearbox

Maintenance

The main component of a planetary gearbox is the planetary gear. It requires regular maintenance and cleaning to remain in top shape. Demand for a longer life span protects all other components of the gearbox. This article will discuss the maintenance and cleaning procedures for planetary gears. After reading this article, you should know how to maintain your planetary gearbox properly. Hopefully, you can enjoy a longer life with your gearbox.
Firstly, it is important to know how to properly lubricate a planetary gearbox. The lubricant is essential as gears that operate at high speeds are subject to high levels of heat and friction. The housing of the planetary gearbox should be constructed to allow the heat to dissipate. The recommended oil is synthetic, and it should be filled between 30 and 50 percent. The lubricant should be changed at least every six months or as needed.
While it may seem unnecessary to replace a planetary gearbox, regular servicing will help it last a long time. A regular inspection will identify a problem and the appropriate repairs are needed. Once the planetary gearbox is full, it will plug with gear oil. To avoid this problem, consider getting the unit repaired instead of replacing the gearbox. This can save you a lot of money over a new planetary gearbox.
Proper lubrication is essential for a long life of your planetary gearbox. Oil change frequency should be based on oil temperature and operating speed. Oil at higher temperatures should be changed more frequently because it loses its molecular structure and cannot form a protective film. After this, oil filter maintenance should be performed every few months. Lastly, the gearbox oil needs to be checked regularly and replaced when necessary.

China 12V 20rpm DC Gear Motor Planetary 36mm Gearbox     planetary gearbox electric motorChina 12V 20rpm DC Gear Motor Planetary 36mm Gearbox     planetary gearbox electric motor
editor by czh 2023-01-15